Cross-Reference
Find the equal.
50,956 products · 253 brands · 31,855 spec sheets — every product cross-referenced to its equals at lookup.
1,213 products
Filtered by spec — refine in the sidebar, or open one for its cross-references. Showing the first 60; add filters to narrow.
outdoor · landscape path
Blue Tooth Range Extender Range extenders are a MUST for every Blue Tooth (BT) System to operate reliably. They repeat and strengthen the communication between all system components, operating as a “mesh network”. Communication signal strength can be reduced by physical obstructions (buildings, landscape features, etc.), intermittent communication interference (competing signals, static, signal noise, magnetic fields, etc.), weather and more. You want a reliable installation! Avoid parts of your BT fixture network going off-line by creating a strong network of range extenders. Range extenders are assigned to a specific network. If you have multiple networks on a property, separate range extender groups will be needed for each network.
- AmeriScapeBTSC600
outdoor · landscape path
BittScape 600 Modernist pathlight with bold angular appearance for both residential and commercial appeal. Taller height provides wider spread of light and visually punctuates the path. Mounting / Installation Wire Lead: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Mounting: Slotted 8.5” large ground stake (standard) Housing: Solid brass. Lens: Frosted polycarbonate lens installed. Light Source Integrated LED module pre-connected to wire lead.
- AmeriScapeFLSC200
outdoor · flood exterior
FloodScape 200 Versatile, wide format wall washer and floodlight with numerous options for lamps, mounting options and optional color-tunable. Mounting / Installation Lead Wire Length: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Mounting: Slotted 8.5” ground stake (standard). Material & Finish Housing: Solid cast brass. Knuckle: Solid cast brass, knob for angle adjustment. Socket: Spring-loaded ceramic bi-pin MR16, with dual contacts and lamp clips. Faceplate: Solid cast brass, with rubber seal, with clear tempered, shock-resistant glass lens. Lenses: Clear lens factory installed. Frosted lens provided in box. Light Source Options Choose factory-installed MR16 lamp below, or factory-installed Bluetooth module. Also available without lamp.
outdoor · flood exterior
FloodScape 200 Bluetooth Versatile, wide format wall washer and floodlight with numerous options for lamps, mounting options and optional color-tunable. Mounting / Installation Lead Wire Length: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Mounting: Slotted 8.5” ground stake (standard). Material & Finish Housing: Solid cast brass. Knuckle: Solid cast brass, knob for angle adjustment. Socket: Spring-loaded ceramic bi-pin MR16, with dual contacts and lamp clips. Faceplate: Solid cast brass, with rubber seal, with clear tempered, shock-resistant glass lens. Lenses: Clear lens factory installed. Frosted lens provided in box. Light Source Options Choose factory-installed MR16 lamp below, or factory-installed Bluetooth module. Also available without lamp.
indoor/outdoor
GradeScape 300 Clear convex lens, for uplighting. A complete family of in-grade lighting solutions for a variety of lighting applications. Combines a rugged brass lid with a non-corrosive polymer housing for long life. Specifications Lead Wire Length: 60” 16AWG wire lead. Housing: Non-corrosive polymer. Lid: Cast brass, attached with 5 color-matched stainless steel screws. Socket: Spring-loaded ceramic bi-pin MR16, with dual contacts and lamp clips.
indoor/outdoor
GradeScape 300 Bluetooth Clear convex lens, for uplighting. A complete family of in-grade lighting solutions for a variety of lighting applications. Combines a rugged brass lid with a non-corrosive polymer housing for long life. Specifications Lead Wire Length: 60” 16AWG wire lead. Housing: Non-corrosive polymer. Lid: Cast brass, attached with 5 color-matched stainless steel screws. Socket: Spring-loaded ceramic bi-pin MR16, with dual contacts and lamp clips.
indoor/outdoor
GradeScape 400 Bluetooth Cast brass lid with open glass lens. Includes integrated Bluetooth RGB LED module standard. Specifications Lead Wire Length: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Housing: ABS plastic can, stainless steel lamp retainer ring. Accessories: Hex louver.
indoor/outdoor · parking area
GradeScape 495 LED High lumen output, integrated-LED well light achieves new levels of lighting performance, matching a line-voltage fixture in low voltage. Get the impressive impact you need to light tall trees, flagpoles, and multi-story structures. Specifications Lead Wire Length: Dual brown 16AWG wire leads (option to daisy chain), first 25’, second 18”. Lid: Cast brass with aged brass finish. Clear convex lens. Housing: ABS plastic can, stainless steel lamp retainer ring. Aiming: Can includes flat end and angled end. Lamp assembly can be fitted to either to allow vertical/flat mounting or angled mounting. Installation: Install in tree wells, tree rings, planting beds, hardscape areas. Avoid installing in areas where pedestrians or vehicles will directly contact fixture.
outdoor · parking area
Pathscape 700 2 tier die-cast area light hat. Pagoda inspired design perfect for any pathway, driveway, flower bed and more. Constructed to evenly diffuse light spread and maximize brightness. Available with your choice of clear or frosted polycarbonate lens. Designed for easy inventory, and mix-and-match design flexibility, our area lights are ordered in two components. Mounting / Installation Lead Wire Length: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18” Mounting: Slotted 8.5” large ground stake (standard) Material Housing: Solid cast brass (hat and stem) Lens: Polycarbonate frosted lens with rubber gaskets both clear and frosted provided Socket: G4 Bi-Pin, Spring-loaded ceramic, with dual contacts and lamp clips Adjustable Beam: Stem incorporates adjustable collar for light spread and glare control
outdoor · parking area
Pathscape 750 Commercial die-cast brass area light hat. Modern and elegant design perfect for any pathway, driveway, flower bed and more. Constructed to evenly diffuse light spread and maximize brightness. Frosted polycarbonate lens silicone in to the hat and commercial grade collar. Designed for easy inventory, and mix-and-match design flexibility, our area lights are ordered in two components. Mounting / Installation Lead Wire Length: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18” Mounting: Slotted 8.5” large ground stake (standard) Material Housing: Solid cast brass (hat and stem) Lens: Polycarbonate frosted lens with rubber gaskets both clear and frosted provided Socket: G4 Bi-Pin, Spring-loaded ceramic, with dual contacts and lamp clips Adjustable Beam: Stem incorporates adjustable collar for light spread and glare control
outdoor · parking area
Pathscape 800 Commercial die-cast brass area light hat. Extra large and shallow design perfect for any pathway, driveway, flower bed and more. Constructed to evenly diffuse light spread and maximize brightness. Frosted polycarbonate lens silicone in to the hat and commercial grade collar. Designed for easy inventory, and mix-and-match design flexibility, our area lights are ordered in two components. Mounting / Installation Lead Wire Length: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18” Mounting: Slotted 8.5” large ground stake (standard) Material Housing: Solid cast brass (hat and stem) Lens: Polycarbonate frosted lens with rubber gaskets both clear and frosted provided Socket: G4 Bi-Pin, Spring-loaded ceramic, with dual contacts and lamp clips Adjustable Beam: Stem incorporates adjustable collar for light spread and glare control
outdoor · parking area
Pathscape 850 Commercial die-cast brass area light hat. Mushroom style design perfect for any pathway, driveway, flower bed and more. Constructed to evenly diffuse light spread and maximize brightness. Frosted polycarbonate lens silicone in to the hat and commercial grade collar. Designed for easy inventory, and mix-and-match design flexibility, our area lights are ordered in two components. Mounting / Installation Lead Wire Length: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18” Mounting: Slotted 8.5” large ground stake (standard) Material Housing: Solid cast brass (hat and stem) Lens: Polycarbonate frosted lens with rubber gaskets both clear and frosted provided Socket: G4 Bi-Pin, Spring-loaded ceramic, with dual contacts and lamp clips Adjustable Beam: Stem incorporates adjustable collar for light spread and glare control
outdoor
Transformer 150 The heart of a low-voltage outdoor lighting system is the transformer. Our rugged professional-grade multi-tap transformer sets the standard for ease of installation and adaptability to standard and app-based controls. Key Features Fully-potted, insulated, single-core transformer Easy on/off, secondary breaker switches on each common tap Two common lug terminals Amp loop to check the primary amperage on the transformer Accepts plug-in-timers, has direct photocell connection Angled terminal strip for easy wire connections, eliminates blind spots Heavy-duty stainless-steel cabinet with integrated mounting bar, lockable Removable bottom panel, 5 knockouts for wire connections Integrated short circuit and overload protection Includes 5’ grounded heavy-gauge power cord ETL tested, in conformance to ANSI/UL 1838 Electrical Specifications 150 watts with 4 taps: 12, 13, 14, 15 volts, Maximum total amps: 1.5A. Use any combination of terminal lugs but do not exceed transformer’s rated wattage on any lug.
outdoor
Transformer 300 The heart of a low-voltage outdoor lighting system is the transformer. Our rugged professional-grade multi-tap transformer sets the standard for ease of installation and adaptability to standard and app-based controls. Key Features Fully-potted, insulated, single-core transformer Easy on/off, secondary breaker switches on each common tap Two common lug terminals Amp loop to check the primary amperage on the transformer Accepts plug-in-timers, has direct photocell connection Angled terminal strip for easy wire connections, eliminates blind spots Heavy-duty stainless-steel cabinet with integrated mounting bar, lockable Removable bottom panel, 5 knockouts for wire connections Integrated short circuit and overload protection Includes 5’ grounded heavy-gauge power cord ETL tested, in conformance to ANSI/UL 1838 Electrical Specifications 300 watts with 4 taps: 12, 13, 14, 15 volts, Maximum total amps: 3A. Use any combination of terminal lugs but do not exceed transformer’s rated wattage on any lug.
indoor/outdoor
Transformer 60
outdoor
Transformer 600 The heart of a low-voltage outdoor lighting system is the transformer. Our rugged professional-grade multi-tap transformer sets the standard for ease of installation and adaptability to standard and app-based controls. Key Features Fully-potted, insulated, single-core transformer Easy on/off, secondary breaker switches on each common tap Two common lug terminals Amp loop to check the primary amperage on the transformer Accepts plug-in-timers, has direct photocell connection Angled terminal strip for easy wire connections, eliminates blind spots Heavy-duty stainless-steel cabinet with integrated mounting bar, lockable Removable bottom panel, 5 knockouts for wire connections Integrated short circuit and overload protection Includes 5’ grounded heavy-gauge power cord ETL tested, in conformance to ANSI/UL 1838 Electrical Specifications 600 watts with 6 taps: 12, 13, 14, 15, 16, 17, 18 volts, Maximum total amps: 6A. Use any combination of terminal lugs but do not exceed transformer’s rated wattage on any lug.
indoor · downlight general
UpScape 395 LED Large sized high lumen output solid brass accent/uplight with integrated LED. Includes frosted lens. Adjustable knuckle is locked with thumbscrew. Ground stake mounting is provided standard. Dual wire leads are factory-installed. Ideal for up lighting tall trees, structures and buildings while being mounted in a planter area. Not intended for downlighting or to be installed in turf areas or areas where there is foot traffic. Mounting / Installation Wire Lead: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Mounting: Slotted 8.5” large ground stake (standard) Material Housing: Solid cast brass. Knuckle: Solid cast brass, knob for angle adjustment. Shroud: Solid cast brass, with turn-to-lock fitting.
indoor · track accent
UpScape 400 Bluetooth High Lumen Output. Powerful integrated LED fixture for maximum impact directional accent lighting. Has integrated RGB LED. Mounting / Installation Wire Lead: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Mounting: Slotted 8.5” large ground stake (standard) Material Housing: Solid cast brass. Lens: Clear glass frosted lens Knuckle: Solid cast brass, knob for angle adjustment. Shroud: Solid cast brass, with turn-to-lock fitting.
indoor/outdoor
UpScape 200 Bluetooth Versatile uplight with numerous options for lamps, mounting options and optional color-tunable, dimmable Bluetooth LED module. Mounting / Installation Wire Lead: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Mounting: Slotted 8” ground stake (standard) Material Housing: Solid cast brass. Knuckle: Solid cast brass, knob for angle adjustment. Socket: Spring-loaded ceramic bi-pin MR16, with dual contacts and lamp clips. Shroud & Lens: Solid cast brass, with dual o-ring seal, with convex tempered, shock-resistant glass lens. Optional Lenses: Frosted lens, hex louver. Light Source Options Choose factory-installed MR16 lamp below, or factory-installed Bluetooth module. Also available without lamp.
indoor/outdoor
UpScape 200 Bluetooth Versatile uplight with numerous options for lamps, mounting options and optional color-tunable, dimmable Bluetooth LED module. Mounting / Installation Wire Lead: Dual 16AWG wire leads (option to daisy chain), first 25’, second 18”. Mounting: Slotted 8” ground stake (standard) Material Housing: Solid cast brass. Knuckle: Solid cast brass, knob for angle adjustment. Socket: Spring-loaded ceramic bi-pin MR16, with dual contacts and lamp clips. Shroud & Lens: Solid cast brass, with dual o-ring seal, with convex tempered, shock-resistant glass lens. Optional Lenses: Frosted lens, hex louver. Light Source Options Choose factory-installed MR16 lamp below, or factory-installed Bluetooth module. Also available without lamp.
indoor/outdoor
The Intelligent Lighting Controls line voltage wall switch & 0-10 volt dimmer provides a stylish solution for spaces where manual dimming control is required. Designed with contractors in mind, the unit is significantly shallower than typical dimmers, resulting in less crowded wall boxes. Additionally, versatile wiring enables usage with or without a neutral connection. For dimming adjustment, intuitive raise and lower buttons are present in addition to the on/off button. Five vertically stacked LEDs are provided to indicate the current dimming level. Configurable dimming parameters include High/Low Trims, Turn on Levels, and Curve Types. This dimmer also matches the ILC family of wall switch occupancy sensors and 0-10V dimming wall switch sensors.
indoor/outdoor
A LightLEEDer-24, -40, or -48 MicroLite Retrofit Insert can take your present outdated or failing MicroLite lighting control system and get it up to todays standards. All of the enhanced features of the LightLEEDer system will be available with this retrofit system from LightSync switches to BAS control. Upgrades are as simple as removing the existing hardware and replacing it with the LightLEEDer hardware provided on a single back plate insert. Reuse existing enclosure, conduit, and wiring. The LightLEEDer programmable lighting controller retrofit insert provides a dependable, flexible, and energy savings controller featuring the robust Reliant40 relay.
indoor/outdoor
The LightSync Occupancy Sensor 8 Input module is designed to power and receive signals from multiple sensors on each of its 8 independent inputs. Eliminate expensive power packs by simply direct- wiring the sensors into the inputs. This module mounts remotely in a location central to the sensors. Each independent input can control any relay(s), group(s), or preset(s) throughout the network.
indoor/outdoor · office general
The ILC Current Limiting Subpanel gives you the ability to limit current on lighting circuits. This gives you the ability to control the calculated load to comply with energy codes like California’s Title 24 that limit the VA (wattage). This subpanel is designed to be installed between the lighting branch circuit breaker and the lighting. These panels are custom configured with 1 to 21 breakers ranging from .5 to 16 Amps.
indoor · surface
The EVO Lite Ceiling Sensor is a low profile ceiling mount sensor designed to install in a standard commercial ceiling. The sensor is provided with dual-tech operation utilizing passive infrared and passive acoustic sensing. Configured with a few simple button presses for easy set-up and adjustment, this sensor supports occupancy and vacancy in a single device. The ELCS also supports traditional 18/3, 24VDC wiring, offering the contractor multiple wiring options, and allowing the ELCS to be used with the 24VDC occupancy sensor inputs of ILC’s LightLEEDer and AP3 systems, as well as most 3rd party systems and power packs.
indoor/outdoor
The EVO Lite G3 Switch is a cost effective, versatile and easy to use hardwired over Cat-5 device. 1 or 2 Zone control with Press-and-Hold Ramp-Up/Ramp-Down dimming from the EVO Lite Power Pack.
indoor/outdoor
The EVO Lite power pack operates one load of lighting or plug load. This power pack includes 12 configuration options, an on-board relay, and 0-10V dimming, integrated into one package for easy installation. The EVO Lite power pack is ideal for small offices or classrooms, made to meet energy code with daylight harvesting, plug load control, occupancy sensing, and vacancy sensing options. It has two RJ-45 ports: one to wire to switches and additional power packs, and another for sensors and additional power packs. This convenient and easy to install power pack can be used as a single device or combined with other EVO Lite power packs, for multi zone operation.
indoor/outdoor · office general
The LightSync EVO Room Controller is a distributed lighting panel that simplifies expansion of a LLEVO or any LightLEEDer panel. The LSEVO-RC supports up to four R20D relays, two photo sensors, and two 6-button G3 switches. Easily connect R20D relays with CAT-5 to control lighting loads, 0-10V dimming, or receptacles. Programming can be easily modified using the ILC Pro Bluetooth app or LightLEEDer Pro software.
indoor/outdoor
INTELLIGENT LIGHTING CONTROLS power pack controllers transform incoming line voltage power to Class 2 low voltage as needed by sensors or other control devices. Additionally, they switch on/off power to the connected lighting load as directed by the sensors and controls. INTELLIGENT LIGHTING CONTROLS power packs utilize a powerful microprocessor to optimize its switching timing in order to ensure long relay life even when controlling high-inrush LEDs and ballast loads. As with all INTELLIGENT LIGHTING CONTROLS products, these power packs are easy to install and incorporate features which reduce contractor labor time. An elongated chase nipple with snaps for quick installation and an optional snap-on low voltage wire chamber make for a hassle free contractor experience. All INTELLIGENT LIGHTING CONTROLS products are proudly made in the USA.
indoor/outdoor
2R seriesrelays are designed to be the longest lasting, most reliable relays available. By incorporating a unique single moving contact, both endurance and reliability are significantly enhanced. These relays have been tested to handle 200,000 full load cycles and 1,000,000 no load cycles. They have two high quality nickel-silver contactsthat can handle today’s high-inrush loads. Relays are available with or without status contacts and are available with variousinterface connectors.
indoor/outdoor
ILC has been designing custom switch stationsfor over 30 yearsto complement our lighting controlsystems. We can design switch plates from smallsingle gang controlstations, to large facility floor plan layouts on a slanted enclosure. The design optionsfor materials, switches,status LEDs, graphics, and mounting are virtually limitless. Switch stations can be designed with a hinged locking door that allowsforstatus viewing but limits access only to those with the key
indoor/outdoor
Momentary Switch Stations are available from ILC in a Decora or toggle style form. These heavy duty switches have a momentary On/Off with a neutral center position. The switches are manufactured by Leviton®, Hubbell®, or Pass & Seymour® and acceptstandard switch plates. Switches can be wired to signal an input to control a relay(s), group(s), or preset(s) in any of ILC’s panels.
indoor/outdoor
The hinged locking doorswitch station provides a secure enclosure for yourswitch stations by limits accessto those who possessthe key. Each station allowsfor installation of LightSync data line switches along with any other low-voltage switch that fitsin a standard electricalswitch box. Custom switch configurations are also available, designed by ILC for yourspecific project. Switch stations are provided in a 1, 2-, 4-, or 8-gang configuration.
indoor/outdoor
The LightLEEDer controller is the key to a powerful, dependable, flexible and energy efficient lighting system. LightLEEDer panels come with our new Reliant40 relays which feature a superior four contact design -- the first true 40Amp lighting relay. Reliant40 relays come in 1-, 2- and 3-pole configurations in a robust breaker-style body. LightLEEDer panels range in size from 4 to 64 relay capacity and are equipped with CAT-5 RJ45 connectors for LightSync data line devices and interconnecting panels. Panels include a keyboard and LCD screen, along with USB and TCP/IP connections for easy programming with our free LightLEEDer Pro Software. Add-on modules are available for connecting to BAS, theatrical, or security systems.
indoor/outdoor · office general
The ILC TR relay provides a unique solution for remote control and panel mount control applications. Because each relay hasits own internal powersupply, it can be mounted virtually anywhere without additional transformers or powersupplies. By incorporating a unique single moving dual contact design, both endurance and reliability are significantly enhanced. TR relays are magnetically latched, requiring only a momentary rectified pulse to open or close the contacts. Isolated pilot contacts are available for indication of relay status at the switch stations. Available TR-Retro relays automatically turn on upon power-up and require a momentary closure to turn the relay on and off.
indoor/outdoor
The LightSync DIgital device hub provides device installation using a home run configuration where the data lines are pulled directly from the devices to a single location. The hub has 20 ports that supplies power for the devices along with renewed data communications. Each port can run up to 1500 feet to devices. The hub is supplied in a NEMA 1 enclosure with a multi-tap transformer and a high voltage divider.
indoor/outdoor
The LightSync G3 data line switch station is a modern, versatile and easy to use digital switch station. The G3 can pre-configured as a Multizone-Dimmer, Scene Switch, or a Non-Dim switch station. These will be configured for 1 to 7 buttons for standard load control, 1 to 6 buttons with dimming buttons for raise/lower or press and hold ramp-up/ramp-down operation that can be configured to dim all, or set of the dimmer outputs controlled. Buttons can be assigned to operate single relays, groups of relays, used for On or Off only operation, activating a relay preset or dimming scene. LED Status indicators for relays on, off, preset, or group state. MZD stations give the operator multi-zone and individual zone adjustment in a single station. LED status indicators for relays on, off, preset, or group state, when an individual zone is selected for dimming the LED will flash for that zone button. Button faces can be changed in the field for color or configuration, and the internal operation can be selected by placing the device in program mode locally, over the LightSync data bus using the diagnostic tool or from the LL-Pro programming software.
indoor
The LightLEEDer EVO Integrated 2 Relay Controller can operate up to two loads. This Controller includes the configuration options of an EVO with two on-board relays and 0-10V dimming integrated into one package for easy installation. The LLEVO-INT-2 relay Controller is ideal for a small office with two zones of lighting control with daylight harvesting or one lighting zone and a plug load. It has RJ-45 ports for local digital LightSync switches, occupancy sensors, and a photo sensor. This convenient and easy to install two relay Controller can be used as a stand-alone device or networked with other LightLEEDer panels.
indoor/outdoor
The LightLEEDer programmable lighting control relay panel is the key to a powerful, dependable, flexible and energy efficient lighting system. LightLEEDer panels come with our new Reliant40 relays which feature a superior four contact design—the first true 40Amp lighting relay. Reliant40 relays come in 1-, 2- and 3-pole configurations in a robust breaker-style body. LightLEEDer panels range in size from 4 to 64 relay capacity and are equipped with CAT-5 RJ45 connectors for LightSync data line devices and interconnecting panels. Panels include a keyboard and LCD screen, along with USB and TCP/IP connections for easy programming with our free LightLEEDer Pro Software. Add-on modules are available for connecting to BAS, theatrical, or security systems.
indoor/outdoor · emergency egress
The LightLEEDer Emergency UL 924 bypass relay control panel will force relay's ON during a normal power outage. This panel has all the same features and functions as a standard LightLEEDer lighting controller, allowing normal control of relays with emergency bypass during a normal power failure event. Relays can be all EM or a combination of normal and EM. Each output has a jumper for selecting Force On, Force Off or No change, this allows for emergency on, load shedding off, or no control selection for each relay. Provided With Phase monitoring module and high voltage dividers. This LightLEEDer Emergency lighting panel is easy to install, no external devices or complicated wiring configurations needed, reducing material and installation costs.
indoor
The LightSync EVO Integrated 2 Room Controller has 2 isolated relays with 0-10V dimming. This controller integrates the control options of an EVO-RC with two on-board relays in one package for easy installation. Up to 3 LSEVO-INT-2-RC room cantrollers can be added to a LLEVO-INT-2 to extend its control into additional rooms or a small office with two zones of lighting control with daylight harvesting or one lighting zone and a plug load. It has RJ-45 ports for local digital LightSync switches, occupancy sensors, and a photo sensor. This convenient and easy to install two relay room controller is great for extending the controls of an LLEVO-INT-2 controller.
indoor/outdoor
The LightSync Digital Power Supply Repeater 4 (LSPSR4) is a remote mounted power supply and data repeater. The PSR4 adds power for LightSync devices and refreshes both LS and LL data communications and is ideal for network distribution. The LSPSR4 has one input and two branch outputs with 2 ports for going up to 4 directions. The power supply supports an additional 20 LS devices and the repeaters refresh data for up to 31 more LL/LS device per branch.
outdoor · landscape path · wall
LightSync Touch Screen 2 is our latest wall-mounted touch controller, ideal for conference rooms or architectural controls. The screen stations have a bright true color TFT display with resistive touch. It is available in 3 sizes to meet your needs; 3.5”, 4.3” and 7.0” and can be mounted in a portrait or landscape position. The 3.5” mounts to a 1-gang electrical box and is provided with a remote-mount power supply. The 4.3” and 7.0” screens are provided with an electrical box that contains the complete interface and power supply for easy installation. The LSTS2 communicates directly to the LightLEEDer controller on the local LightSync network. Software is provided which allows customizing the layout and programming. They support up to 15 active screens with buttons, status, slide dimmers, plus a logo home screen. Choose standard color sliders, including red, green, or blue. Warm to cool color tuning for CCT control, or full spectrum color wheel for RGB control. Each station comes pre-configured with 5 Scene buttons with capture-ability, along with an Off and 4 slide dimming controls.
indoor/outdoor
Intelligent Lighting Controls wireless power pack controllers switch on/off power to a connected lighting load as directed by wirelessly linked sensors, photocells, and wall controls. Additionally, the unit’s 0-10V dimming option greatly simplifies applications where dimming control from multiple switch locations is required. For applications where a hybrid wireless/wired architecture is desired, this wireless power pack can also be ordered with auxiliary low voltage connections.
indoor · surface
ILC provides a full line of occupancy sensors to meet your facilities requirements. Sensors are available with passive infra red detection or dual-technology sensors that combine infrared detection along with sonic detection for a more robust sensor. Sensors are available in many types including wall switches, ceiling mount, corner mount and surface mount.
indoor/outdoor · office general
The ILC Remote 20 (R20) and Remote 20 Dimming (R20D) relays are designed to be mounted at the power junction box or lighting fixture for direct control of the lighting load. Relays are controlled from the EVO panel using a standard CAT-5 cable connection to the R20 relay RJ-45 jack. The R20 series relay uses oversized contacts designed to handle LED inrush current. Tested at 16 Amps electronic driver that can commonly exceed 200% of running current of the R20D latching relay load. The R20D has galvanically isolated 0-10V dimming which allows for class 1 wiring of the low voltage dimming. Loss of power to the LLEVO panel will force dimmer output level to 100%.
indoor/outdoor
The ILC Remote 20 Amp, Emergency Bypass Relay combines normal relay operation with a UL 924 bypass relay in one convenient package. Relays are available in both a wired (R20D-EM) and wireless (WR20D-EM) version that uses the 915MHz radio frequency for communication to ILC wireless devices. When normal power is lost the EM relay will automatically force ON the EM load and send dimming to 100%. When normal power is restored the device will return to normal control. The R20D-EM and WR20D-EM have a relay test button, and a wired input that can be used for a remote test switch or as an override connection from a fire alarm system.
indoor/outdoor
The INTELLIGENT LIGHTING CONTROLS family of wall switch occupancy/vacancy sensors provides a simple and cost effective lighting control solution for many applications. Just like its line voltage counterpart, the low voltage INTELLIGENT LIGHTING CONTROLS 0-10V dimming wall switch sensor is designed with contractors in mind. Less than 1” deep, the unit is 25-40% shallower than typical dimmers and sensors, resulting in less crowed wall boxes. INTELLIGENT LIGHTING CONTROLS products utilize the latest passive infrared technology and digital signal processing techniques to provide unmatched motion detection performance. These units are also available with an integrated microphone to provide overlapping passive acoustic occupancy detection for rooms with obstructions or where occupant motion is limited. For dimming adjustment, intuitive raise and lower buttons are present in addition to an on/off button.
indoor/outdoor
The Apprentice 3 programmable lighting control panel is an energy saving lighting controller. You can network up to 48 control points and 64 LightSync™ devices per network and connect via easy to use RJ-45 ports. Connect and program panels using a USB port on a laptop and our free Apprentice 3 software. Add-on cards are easy to install and and add the following capabilities: BACnet, LonWorks, N2, MODBUS, TCP/IP, or modem interface, DMX control and DTMF telephone switching. Also optional remote mount 0-10V isolated dimming control modulesforstandard daylight harvesting operations.
indoor/outdoor · wall
LightSync Touch Screen Stations provide the ultimate in wall-mounted touch control, ideal for conference rooms or architectural controls. These multi-screen touch stations communicate directly to the lighting control system on the LightSync network. Choose the 3.5" with 320 x 240 resolution, 4.3”screen with a 480 x 272 resolution, or the 7.0"screen with a 800 x 480 resolution; both have a 65K true color LCD screen with resistive touch. The touch controlstations are a complete package, provided with an electrical box that containsthe complete interface, just connect to the LightSync data line and a 120VAC source. The touch screen has a capacity of up to 16 screens that can be designed with a variety of controls and security. With the use of the included intuitive software, youwill be able to design the controlstation screensto your facility's needs.
- LumenwerxAERA2CYLINDERPENDANTspec →
indoor/outdoor · cylinder accent
AERA 2" CYLINDER
- LumenwerxAERA2CYLINDERSURFACEspec →
indoor/outdoor · cylinder accent
AERA 2" CYLINDER
- LumenwerxAERA2CYLINDERWALLspec →
indoor/outdoor · cylinder accent
AERA 2" CYLINDER
- LumenwerxAERA2DEEPROUNDRECESSEDTRIMspec →
indoor/outdoor
AERA 2" DEEP
- LumenwerxAERA2DEEPROUNDRECESSEDTRIMLESSspec →
indoor/outdoor
AERA 2" DEEP
- LumenwerxAERA2DEEPSQUARERECESSEDTRIMspec →
indoor/outdoor
AERA 2" DEEP
indoor/outdoor
AERA 2" DEEP
- LumenwerxAERA2DOWNLIGHTROUND
indoor · downlight general · recessed
-1382
- LumenwerxAERA2DOWNLIGHTROUNDBEVELFLANGEDTRIM
indoor · downlight general · recessed
-1382
- LumenwerxAERA2DOWNLIGHTROUNDBEVELTRIMLESS
indoor · downlight general · recessed
-1382